VT-MIPM-138-D IPm® Industrial RTU

Performance Specifications

• Industrial PowerPC 333MHz (32 bit data bus)
• Operating system embedded open-source Linux
• Dynamic memory (RAM) 512 MB for program execution, dynamic variables, dynamic file system, etc.
• Program memory (Flash) 512 MB for Linux OS, program storage and file system
• Retained memory (RAM) 8 MB (battery-backed) for datalogging and retained variables
• Real-time clock battery-backed for time stamping and other operations
• I/O Expansion RS-485 or Ethernet
• Datalogging support
• IEC 61131 programming, Red Lion Workbench
• High Level C programming
• Battery life 10+ years
• Real-time clock resolution 1ms
• I/O Expansion E2 or E3 I/O Modules

Ethernet Port 

• 10/100BaseTx (auto-detecting)
• RJ45 connection (auto-crossover)
• Protocols TCP/IP, ARP, UDP, ICMP, DHCP, Telnet, SSH, Modbus/TCP, Sixnet UDR, FTP

Serial Port 

• Up to 115,200 baud
• RS-485 Port A screws (485+, 485-, GND) (2-wire half-duplex)
• RS-232 Port B RJ45 (TD, RD, CTS, RTS, CD, DTR, DSR, GND)
• RS-232 Port D Screws (TD, RD, GND)
• Protocols Master and slave modes; Sixnet and Modbus RTU / ASCII     

Discrete Inputs

• 12 channels sourcing or sinking (jumper/software selectable)
• Guaranteed ON voltage 9 VDC
• Maximum voltage 30 VDC
• Guaranteed OFF voltage 5.0 VDC and 1.5 mA DC
• Input resistance and current 10K Ohms and 3 mA @ 24 VDC
• Filtered ON/OFF delay 25 mS (20 Hz max. counting) for contact bounce filtering
• Fast ON/OFF delay 4 mS (100 Hz max. counting)
• Count rate (see above) (10 KHz on channel 1 only)
• Counter modes pulse, rate and run time
• Poll time (all channels) 5 mS to 20 mS configuration dependent

Discrete Outputs

• 8 channels – sourcing 10-30 VDC
• Min. and max. output load 1 mA to 1 Amp sourcing per channel
• Max. OFF state leakage 0.05 mA
• Inrush current 5 Amps (100 mS surge)
• Typical ON characteristics 0.3 Ohms resistance and 0.3 VDC voltage drop @ 1A
• Poll time (all channels) 5 mS to 20 mS configuration dependent

Analog Inputs

• 6 channels – current or voltage selectable
• Full scale range 4-20 mA
• A/D and input resolution 16 bits (0.003%); 2 uA (current range)
• Full scale accuracy +/-0.1% (@20°C) (factory calibration)
• Span and offset temp. coeff. +/-50 ppm per °C
• Input impedance 100 Ohm (current range), 80 K Ohm voltage
• Current protection Self-resetting fuses (for 4-20 mA range)
• DMRR 66 dB at 50/60 Hz (differential mode rejection)
• CMRR (common mode rejection) Not applicable since analog inputs are single ended.
• Fastest update time 50 mS (both channels) – configurable for longer integration times for better noise filtering

Environmental

• DIN-rail or panel-mount
• Input power 10-30 VDC
• Input current 100 mA @ 24 VDC (typical); 1 A per each discrete output (8 outputs maximum)
• Temperature -40 to 70°C (-40 to 85°C storage)
• Humidity 5% to 95% RH (non-condensing)
• Flammability UL 94V-0 materials
• Electrical safety UL 508, CSA C22.2/14; EN610101-1:2010: CE
• EMI emissions FCC part 15, EN 61000-6-4:2007; EN 300 386 v1.5.1
• EMC immunity EN 61000-6-2:2005
• Vibration IEC 60068-2-6 Test Fc; 60870-2-2 Class Cm; IEC 60068-2-27
• Hazardous locations ISA12.12.01, CSA C22.2/213, Class 1, Division 2 Groups A, B, C, D
• ATEX (Zone 2)  II 3 G Ex nA IIC T4A
• ABS Type Approval 21-2078121-PDA
• Size 4.75"L x 3.83"W x 4.13"H (12.07cm L x 9.73cm W x 10.48cm H)

Software & Firmware

Knowledge Base